antenna hoisting using pulley and rope

  • recovery winch

    recovery winch

    Heavy-duty winch with 5-hp, series-wound motor lets you quickly and safely recover a stuck vehicle. Premium winch is fully sealed for complete submersion in water or mud. It includes a … Read More

    Consult Online
  • electric bed hoist

    electric bed hoist

    LIMICAR Electric Hoist 1320LBS Overhead Hoist Lift Electric Hoist Crane Garage Ceiling Pulley Winch Remote Control Power System with Premium Straps 6.6'x3" Lift Sling 4.3 out of 5 stars 21 … Read More

    Consult Online
  • Peadar, EI2IF will be putting up a new antenna shortly and I made this video to illustrate the method I use at my QTHR to raise and lower my dipole antenna u

  • Some Basics About Tree Supported Antennas – antenna tensioner

    A support rope is looped through the tree top with one end secured to a high grade pulley so that the pulley can be hoisted to its position in the tree. A second rope is attached to the antenna and passed through the pulley and fastened to a counterweight on the ground. The support rope and pulley is then pulled to its position near the tree top.

  • use 5/16 diameter rope. And I always use marine grade pulleys which will not rust or corrode. Now thread the antenna halyard rope through the pulley and pull enough through so that you can still reach the end of it after you've hoisted the pulley with the rigging line. Once this assembly is completed, pull on the "back" side

  • May 18, 2020 · Guy Rope Polyester is the best choice for antenna support rope or any outside application where strength, less stretch, UV and abrasion resistance is important. Unlike Nylon, Polyester Rope is less elastic and therefore stretches much less. In fact Nylon Rope will stretch anywhere from 15 – 25% percent at it’s break point.

  • use the medium weight rope you used when installing your wire antenna support Tie one end to the support rope. Pull down 'antenna support' rope from the antenna end. If the rope is frayed, replace

  • First, assemble the pole when you get on-site at the antenna tower. Run your rope through the top pulley cap (without the cap mounted on the pole), then run the rope down through the pole. You will need to let gravity pull the rope through. so tilt the pole up as far as you can and jam rope down it.

  • antenna hoisting using pulley and rope
  • An ingenious, easy- to-implement tree The support for your

    the antenna, and the end you’ll be using to pull the antenna up and lower it down. The free length of the antenna end will have to be at least twice the distance from the branch to the ground. If it’s shorter than that, you can temporarily tie on another rope to extend its length. Figure 2 — Pulling the rope in place over the tree limb

  • I just wrap a piece of loose rope around the base somewhere I can reach, use some chain repair links (cheap man's clip) to hold the ropes from the pulley close to the trunk at the bottom and suspend about 20 lb rocks near the ground to keep tension on the antenna. But then I'm using CCS wire. Your weight may vary.

  • Jan 03, 2018 · Attach the rope first to the bottom of the upper fixed pulley, then loop the rope down through the wheel on the moveable lower pulley. Now, loop the rope back up through the top fixed pulley. Make sure the rope is fully seated into the grooves on the pulley wheels. Proceed to lift the weight by applying downward or lateral pressure on the rope.

  • Jan 19, 2021 · Adding the Rope Once construction is completed, it is time to weave the ropes through the pulleys. If you will be hoisting several items using independent ropes, consider using different colors to avoid confusion. Some of the eye hooks can be left without pulleys for later installation.

  • use 5/16 diameter rope. And I always use marine grade pulleys which will not rust or corrode. Now thread the antenna halyard rope through the pulley and pull enough through so that you can still reach the end of it after you've hoisted the pulley with the rigging line. Once this assembly is completed, pull on the "back" side

  • The Amazing Gin Pole Lifter! : 10 Steps (with Pictures

    First, assemble the pole when you get on-site at the antenna tower. Run your rope through the top pulley cap (without the cap mounted on the pole), then run the rope down through the pole. You will need to let gravity pull the rope through. so tilt the pole up as far as you can and jam rope down it.

  • the antenna, and the end you’ll be using to pull the antenna up and lower it down. The free length of the antenna end will have to be at least twice the distance from the branch to the ground. If it’s shorter than that, you can temporarily tie on another rope to extend its length. Figure 2 — Pulling the rope in place over the tree limb

  • About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features Press Copyright Contact us Creators

  • Feb 03, 2018 · Since pulleys of this type are almost impossible to find in most areas of the country, I still stock one of these pulleys which is very well suited for use with the high quality antenna support rope that we sell. This pulley is manufactured by one of the preeminent makers of sailboat rigging.

  • #harborfreighttools #gambrelpulleyhoist #deerhuntingSUPPORT STKO HERE: https://www.amazon.com/shop/shoottokilloutdoorshttps://www.patreon.com/STKOIf you have

  • Coaxial Cable

    2.Hoisting the Cable Hoist Line. Use a hoist line that supports the total weight of the cable. Refer to the table for approximate cable weights per foot and per meter to calculate total cable weight. Pulleys. Use a strong pulley at both the top and bottom of the tower to guide the hoist line, as illustrated. Cable Reel.

  • Jan 03, 2018 · When the pulley is fixed to a solid anchor and a rope is threaded through the grooves on the pulley's wheel, it can be used to lift heavy weights much more easily than doing it by brute force. And you can double the effectiveness of a pulley system by increasing the number of pulleys in the setup.

  • Jan 19, 2021 · During installation and use, automatic garage door operation should absolutely be terminated. It is extremely dangerous to try and hoist a person using this home-built pulley system. At all times, stick to the recommended weight limit. Be sure that the ropes are in good condition, with no signs of fraying which could weaken the strength and

  • Pulley systems are used to provide us with a mechanical advantage, where the amount of input effort is multiplied to exert greater forces on a load. They are typically used for hauling and lifting loads but can also be used to apply tension within a system such as in a Tensioned Line or Tyrolean.

Weihua has been engaged in crane R&D and manufacturing,main product is overhead crane,electric hoist,winch,gantry crane,jib crane,port crane,container crane,KBK,foundry crane,explosion proof overhead crane,crane accessories.